YRT80High Precision Rotary Table Bearing80*146*35mmCNC machine tool rotary table bearings
YRT80bearing consist of a thrust/radial housing washer, a thrust/radial shaft washer, a thrust washer, two Axial needle roller and cage assemblies and a group of radial cylindrical roller . Housing washer and shaft washer have equally spaced fitting bolt. This kind of bearingsYRT80have high axial load and radial load ,and high tilting rigidity and high precision.YRT80can be used to the machine tool and other high precision machinery of the rotary table or sub-set, and also can be used for chuck, measuring instruments and test equipment and rotary table configuration.
bearing type
12
80 | 146 | 35 | 23.35 | 12 | 130 | 92 | 138 | 5.6 | 10 | 4 | 10 | 4.6 | 12 |
YRT100 | 100 | 185 | 38 | 25 | 12 | 160 | 112 | 170 | 5.6 | 10 | 5.4 | 16 | 5.6 | 15 |
YRT120 | 120 | 210 | 40 | 26 | 12 | 184 | 135 | 195 | 7 | 11 | 6.2 | 22 | 7 | 21 |
YRT150 | 150 | 240 | 40 | 26 | 12 | 214 | 165 | 225 | 7 | 11 | 6.2 | 34 | 7 | 33 |
YRT180 | 180 | 280 | 43 | 29 | 15 | 244 | 194 | 260 | 7 | 11 | 6.2 | 46 | 7 | 45 |
YRT200 | 200 | 300 | 45 | 30 | 15 | 274 | 215 | 285 | 7 | 11 | 6.2 | 46 | 7 | 45 |
YRT50,YRT80YRT100,YRT120,YRT150,YRT180,YRT200,YRT260,YRT325,YRT460, YRT rotary table YRT series :
YRT580,YRT650, YRT850 ,YRT950,YRT1030
YRTM series:
YRTM50,YRTM80,YRTM100,YRTM120,YRTM150,YRTM180,YRTM200,YRTM260,YRTM325,YRTM460,YRTM580,YRTM650,YRTM850,YRTM950,YRTM1030
Leading Products
high precision YRT rotary table bearings, YRT series ,YRTS series ,YRTM series, ZKLDF series.The precision rate has reached P5/P4/P2,ranging from 50mm --- 1300mm
Design & Installation forYRT80:
Structure with the requirements shown in Figure 1
Retaining screws secure the bearing components during transport. For installing the bearing easier, the screws should be loosened before fitting, and secured again or replaced by positioning screws after fitting.
The L-section ring can be fitted with unsupported or supported ring.
a) Without supported ring, the bearing type isYRT80.
b) With supported ring, the bearing type isYRT80-VSP.And the whole surface of L-section should be supported.
Mounting forces must only be applied to theYRT80bearing ring to be fitted, never through the rolling elements.
Tighten the fixing screws in crosswise using a torque wrench (shown in figure 2).
Don’t separate or interchanged bearing components during fitting and dismantling.
Starting friction torque can be 3 to 3.5 times as high as the value of friction torque in the dimension tables.
